I’m working on another one of these for a buddy. I was going to start it before changing the Vape ignition/charging. But left cylinder has no spark. Then I found the flywheel nut loose and flywheel loose. So I think it was parked due to now spark on that side. I suspect the condenser (points tested ok).
So I will change install the Vape and go from there.
Benelli 250 2C
Re: Benelli 250 2C
by Lotus54 » Wed May 01, 2024 5:26 pm
1976 OSSA Super Pioneer- 78 Benelli 750 sei, 1980 Benelli 250 Quattro, 72 250 2C Benelli, 68 Benelli Dynamo trail, 76 OSSA GPII Phantom, Beta XTrainer 300, 72 BSA 500 SS, Lotus Elan S3
-
Lotus54 - Posts: 634
- Images: 0
- Joined: Tue Jun 12, 2012 9:13 pm
Re: Benelli 250 2C
by John H » Sun May 05, 2024 8:37 pm
Sounds like you are sold on Vape ignitions. I have one on the 370 Pursang but don't have instructions for setting it up. Hadn't thought about a loose flywheel.
[i][color=#4040BF]John[/color][/i]
- John H
- Posts: 1130
- Images: 8
- Joined: Wed Jun 13, 2012 10:19 am
- Location: Northwest
Re: Benelli 250 2C
by Lotus54 » Tue May 07, 2024 9:18 pm
This is third one Ive done. Second 250- so it is going a lot easier.
Flywheel is located just by taper, but i hve had no issues. Just a bit moe ok to mke ure correct lotcation.
Will be ready for Z1 wiring soon.
Flywheel is located just by taper, but i hve had no issues. Just a bit moe ok to mke ure correct lotcation.
Will be ready for Z1 wiring soon.
1976 OSSA Super Pioneer- 78 Benelli 750 sei, 1980 Benelli 250 Quattro, 72 250 2C Benelli, 68 Benelli Dynamo trail, 76 OSSA GPII Phantom, Beta XTrainer 300, 72 BSA 500 SS, Lotus Elan S3
-
Lotus54 - Posts: 634
- Images: 0
- Joined: Tue Jun 12, 2012 9:13 pm
Re: Benelli 250 2C
by Lotus54 » Thu May 09, 2024 6:44 am
New flywheel/stator mounted and timed
- Attachments
-
- IMG_8390.jpeg (36.62 KiB) Viewed 66225 times
1976 OSSA Super Pioneer- 78 Benelli 750 sei, 1980 Benelli 250 Quattro, 72 250 2C Benelli, 68 Benelli Dynamo trail, 76 OSSA GPII Phantom, Beta XTrainer 300, 72 BSA 500 SS, Lotus Elan S3
-
Lotus54 - Posts: 634
- Images: 0
- Joined: Tue Jun 12, 2012 9:13 pm
Re: Benelli 250 2C
by John H » Thu May 09, 2024 9:07 pm
Interesting that some other bikes attached these rotors without a key. The Z1R is the same and it causes real problems as the starter clutch bolts to the rotor.
[i][color=#4040BF]John[/color][/i]
- John H
- Posts: 1130
- Images: 8
- Joined: Wed Jun 13, 2012 10:19 am
- Location: Northwest
Who is online
Users browsing this forum: No registered users and 3 guests